CUTEK® Restore is a powerful timber cleaning agent that restores stained, weathered and grey wood back to its original appearance.

CUTEK® Restore is effective in removing stubborn stains caused by tannins, water, iron, resins, mould and fungus. It also removes the common invisible glaze (mill glaze) to prepare newly sawn or machined timber for coating.

CUTEK® Restore will brighten, clean and restore wood to look like new, ready for CUTEK® Extreme CD50. 

Details
  • Category
    Timber & Wood Stains, Timber Coatings, Timber Stains
  • Brand
    CUTEK®
Scope of use
  • Restoration of stained or high traffic areas such as decks, marine jetties, boardwalks, etc.
  • Rejuvenation of external and weather affected or greyed timber such as decking, cladding, fences, shingles, etc.
  • CUTEK® Restore will not remove paint and wood coatings from your timber. In these instances, remove with CUTEK® Wood Stripper.
Features
  • Powerfully restores timber: Brings weathered, greyed/silvered wood back to original appearance
  • Prepares new timber for coating: Removes common invisible glaze (‘mill glaze’) from newly sawn timber or machined timber
  • Removes stubborn stains: Such as iron stains, water marks, tannins, resins, mould and fungus
How to apply

Prepare

It is important for the user to determine the suitability of the CUTEK® Restore for its intended application. ALWAYS test product on a small test area prior to applying to any large sections. As the species and condition of timber can vary significantly, testing will enable you to accurately estimate the dilution, time and volume of CUTEK® Restore required to complete your project.

Safety and precautions:

Before you begin to Prepare and Protect your timber, note the hazards and precautions and ensure that you have obtained and know how to use the correct safety equipment as detailed in the Safety Data Sheet.

When using CUTEK® Restore, all adjacent surfaces and vegetation must be adequately protected. It is also important to be aware of the potential for wind drift into areas with cars or pedestrian traffic when rinsing. Water flush all equipment, vegetation, paths, concrete, asphalt and other adjacent surfaces before and after contact.

Coverage:

Spreading rate is approximately 1 Litre of CUTEK® Restore per 5-8m2 of surface area to be restored.

CUTEK® Restore is a powerful timber restoring agent and can be used diluted or undiluted. Coverage can vary depending on the smoothness and density of your timber as well as the severity of staining and/or weathering. Always test to determine if your chosen dilution is effective in the restoration of your specific timber.

Application:

Wet your timber prior to applying CUTEK® Restore. Apply CUTEK® Restore liberally to wetted timber with a brush, roller, lambswool applicator or broom.

Let CUTEK® Restore do the work by leaving it on the surface for 1 hour to 24 hours depending on the severity of staining or discolouration. It may be necessary to scrub stubborn stains moderately with a stiff fibre brush.

Removal:

Once CUTEK® Restore has cleaned the timber, it must be water rinsed off thoroughly. For best results, power rinse with a high-pressure washer set to approximately 50 bar (750 p.s.i.) with a fan jet pattern. Removal with a garden hose is not sufficient.

Caution must be used when cleaning soft timber. Reduce the pressure or adjust distance from the substrate to avoid damaging the sapwood. It is important to adjust your cleaning process to avoid damage to the wood fibre.

The longer that CUTEK® Restore is left on the substrate, the greater the rinse time required. Clean from the highest point and work down methodically using long even strokes in the direction of the grain.

Note: certain types of wood surfaces may leave a raised grain effect after pressure washing is completed. Sanding or poly pad scrubbing may be required to smooth out this condition.

Do not use “turbojets” on timber.

SKU: cutek-r-1
Visit Website

About the
Seller

CUTEK® is a powerful wood protection system… but is also so much more than that. CUTEK® timber oils offer powerful protection while enhancing the natural beauty of timber. CUTEK® timber oils diffuse deeply into timber to repel moisture, maintain structural integrity and ensure the longest possible service life.

What sets CUTEK® oils apart is their ‘self-healing’ action. Once diffused, CUTEK® oils remain permanently mobile in the timber actively driving out moisture to minimise cupping, warping and splitting, even after being cut or perforated with fasteners. CUTEK® penetrating oils have a 30-year proven track record of standing up to our New Zealand climate and other harsh environments around the world.

At ArchiPro we recognise and acknowledge the existing, original and ancient connection Aboriginal and Torres Strait Islander peoples have to the lands and waterways across the Australian continent. We pay our respects to the elders past and present. We commit to working together to build a prosperous and inclusive Australia.